PETROSCRAP.COM

Nylon Round Rod, White, 1/16″ OD, 72″ Length Heat Deflection Temperature Under Load is 200 FResists Common Solvents, Esters, Ketones, Alkali’s and Dilute AcidTough and Impact ResistantLow Coefficient of FrictionEasily Machined Nylon 6/6 Rods and Sheet are typically used as material for insulators, shaft bearings and bushings, wear strips, hinges, gears, and general fixturing. Heat deflection temperature at 264 PSI: 200F (93C). Color: Natural.A tough general purpose plastic with outstanding resistance to organic chemicals, acids and alkalis, Nylon 6/6 wears well against other surfaces and has a low coefficient of friction. It is readily machinable and may be milled, turned and cut with…. Click Here to Read More

Polypropylene Sheet, Opaque White, 3/32″ Thick, 12″ Width, 12″ Length Limited Cycles of Steam SterilizationHighly Resistant to Corrosive MaterialsOutstanding Chemical ResistanceContinuous Temperature 180 – 200 FLow Cost Polypropylene is in the family of polyolefins and offers a combination of outstanding physical, chemical, mechanical, thermal, and electrical properties not found in any other thermoplastic. Polypropylene is highly resistant to corrosive materials, and has high temperature resistance along with superior resistance to solvents, degreasers, as well as electrolytic attack. Common uses are battery cases, acid handling equipment, metal plating barrels, and fume hoods. It has…. Click Here to Read More

Polycarbonate Round Rod, Clear, 1/2″ OD, 24″ Length High Impact ResistanceTemperature Range of -60 to 270 FHigh RigidityDuctility of Softer Lower Modulus PlasticsTransparent Clear Commonly referred to as Lexan, Polycarbonate is a thermoplastic used in many applications that require high impact strength, a large temperature service range, excellent electrical properties, and dimensional stability. Polycarbonate Sheet is smooth and clear. Normal forming temperature of Polycarbonate is 375F (190C). List Price: $ 10.49 Price: $…. Click Here to Read More

Phenolic XX Paper Grade Sheet, Natural, 0.5″ Thick, 6″ Width x 12″ Length Phenolic XX Paper GradeMil P 3115NEMA XXType PBELP 509 Phenolics are also known by various trade names such as Micarta, Spauldite, and Texolite. They are high pressure laminates that are hard and dense. They are made by applying heat and pressure to a series of layered materials such as cellulose, cotton fabric, synthetic fibers, glass fibers or woven fabrics and then impregnated with synthetic resin. Once the layers are heated and pressure is applied, the layers are transformed into a high pressure thermosetting industrial laminate. List Price: $ 10.58 Price: $…. Click Here to Read More

Acetal Round Rod, Black, 2″ OD, 24″ Length Excellent machinabilityExcellent Dimensional StabilityTough and Impact ResistantLow Coefficient of FrictionModerate Chemical Resistance Commonly referred to as Delrin, this Acetal is a useful replacement for metal in many applications such as gears, pulleys, impellers, etc. Easily machined with all standard machine tools. Its machinability is equal to or better than free machining brass in the normal operations of milling and turning to threading and tapping. This Acetal Resin offers a high degree of dimensional stability, toughness, impact strength, low coefficient of friction and fair chemical resistance.Note: Delrin may cause allergic…. Click Here to Read More

HDPE (High Density Polyethylene) Round Rod, White, 1″ OD, 12″ Length Abrasion ResistantLow coefficient of FrictionGood Energy AbsorptionResists Stress CrackingModerate Temperature Rating High Density Polyethylene (HDPE) is high impact strength with a higher temperature rating than Low Density Polyethylene. It has higher tensile strength, good energy absorption, abrasion resistance and resists stress cracking. HDPE has a low coefficient of friction and is self lubricating. Applications include low speed bearings, tank/chute/bin linings, packing rings in chemical applications. HDPE is in the family of polyolefin’s. List Price: $ 12.19 Price: $…. Click Here to Read More

PTFE Sheet, White, 0.06″ Thick, 12″ Width, 12″ Length Sheet FormMax Temp 500 FVery Low Coefficient of FrictionExtremely Low Dielectric ConstantUV and Ozone Resistant PTFE sheet (Polytetrafluoroethylene) sometimes known as Teflon has established itself as a tough, durable polymer, possessing a unique combination of electrical, chemical, mechanical and thermal properties unmatched by any other single substance. Maximum operating temperature -350 degrees to 500 degrees F. This material should not be heated to temperatures above 752 degrees F (400 degrees C). PTFE Sheet is available in a series of nine thicknesses from 0.005 inches to 0.500 inches. In addition, three of these thicknesses…. Click Here to Read More

ABS Sheet, Natural Beige, 3/8″ Thick, 6″ Width, 12″ Length Good Chemical ResistanceHard SurfaceEasily MachinedGood for Vacuum FormingGood Impact Resistance General purpose grade ABS combines heat stability, chemical resistance and surface hardness of Acrylonitrile with the toughness and impact resistance of Butadiene and the rigidity and machineability of Styrene…to give you ABS with easy formability and high gloss. Good for vacuum forming, with a normal forming temperature at 295 degrees F (146 degrees C) – Rockwell Hardness R-105. Color: Natural (Beige) List Price: $ 16.82 Price: $…. Click Here to Read More

UHMW (Ultra High Molecular Weight) Polyethlylene Round Rod, White, 1″ OD, 36″ Length Low Coefficient of FrictionVery High Impact StrengthExcellent Abrasion ResistanceSelf LubricatingHighly Resistant to Corrosives Ultra high molecular weight polyethylene (UHMWPE), also known as high-modulus polyethylene (HMPE) or high-performance polyethylene (HPPE), is a thermoplastic. It has extremely long chains, with molecular weight numbering in the millions, usually between 2 and 6 million. The longer chain serves to transfer load more effectively to the polymer backbone by strengthening intermolecular interactions. This results in a very tough material, with the highest impact strength of any…. Click Here to Read More

UHMW (Ultra High Molecular Weight) Polyethlylene Round Rod, White, 1″ OD, 36″ Length Low Coefficient of FrictionVery High Impact StrengthExcellent Abrasion ResistanceSelf LubricatingHighly Resistant to Corrosives Ultra high molecular weight polyethylene (UHMWPE), also known as high-modulus polyethylene (HMPE) or high-performance polyethylene (HPPE), is a thermoplastic. It has extremely long chains, with molecular weight numbering in the millions, usually between 2 and 6 million. The longer chain serves to transfer load more effectively to the polymer backbone by strengthening intermolecular interactions. This results in a very tough material, with the highest impact strength of any…. Click Here to Read More

Teflon FEP Round Rod, White, 3/16″ OD, 12″ Length Temperature Range -348 to 400 FExtreme Chemical ResistanceLowest critical surface energy of all plasticsLowest Refractive Index of All PlasticsExtremely low dielectric constant and dissipation factor Teflon FEP Rod has excellent chemical, thermal, and electrical stability. It retains a high percentage of its useful properties from cryogenic to elevated temperatures -348 F to 400 F. It has the lowest critical surface energy of all plastics, which makes it an excellent water and oil repellent for non-stick and mold release. Teflon FEP has an extremely low dielectric constant and dissipation factor. Excellent resistance to UV, Ozone, and…. Click Here to Read More

Nylon Round Rod, Beige, 3/8″ OD, 24″ Length Heat Deflection Temperature Under Load is 200 FResists Common Solvents, Esters, Ketones, Alkali’s and Dilute AcidTough and Impact ResistantLow Coefficient of FrictionEasily Machined Nylon 6/6 Rods and Sheet are typically used as material for insulators, shaft bearings and bushings, wear strips, hinges, gears, and general fixturing. Heat deflection temperature at 264 PSI: 200F (93C). Color: Natural.A tough general purpose plastic with outstanding resistance to organic chemicals, acids and alkalis, Nylon 6/6 wears well against other surfaces and has a low coefficient of friction. It is readily machinable and may be milled, turned and cut with…. Click Here to Read More